Vega D86_D87 Hydrostatic pressure transmitters Bedienungsanleitung PDF herunterladen (Seite 29)

Pressure transmitters D86/D87 29

Setup

1.2.3.1.1

1.2.3.1.2

Note:

After entering a parameter, push "

ENTER

" and then "

SEND

Confirm the message to switch over to manual operation with "

Confirm the message to reset to automatic operation also with "

Only then will the adjustment be stored in the sensor and take effect.

Menu windows are displayed but not

supported by the sensor.

Saving of adjustments carried out here is

therefore not possible.

1.4.3.1.3

1.4.3.1.2

Low: In case of failure, current output

goes to 22 mA

High: In case of failure, current output

goes to < 3.6 mA

1.4.3.2

1.4.3.1

}

Off

Not used

None

Unknown

Special

Sensor signals measured values only on

request

Sensor signals measured values

unrequested

Choice is not supported

1.4.3.2.3

1.4.3.2.4

Leave the Burst-mode in

OFF position

Choice is not supported

1.2.3.1.1.1

1.2.3.1.2.1

1.4.3.1.3

1.4.3.1.3.1

Generic: D84

Current applied

process value: 97.112

mbar

1 Set as 4 mA value

2 Read new value

3 Leave as found

ABORTENTER

Generic: D84

Current applied

prosess value :96.262

mbar

1 Set as 20 mA value

2 Read new value

3 Leave as found

ABORT ENTER

Generic: D84

Choose analog output

level

1 4 mA

2 20 mA

3 Other

4 End

ABORTENTER

Generic: D84

WARN - Loop should be

removed from

automatic control

ABORT OK

Generic: D84

Set the:

1 4 mA

2 20 mA

3 Exit

ABORT ENTER

Generic: D84

Apply new 20 mA input

ABORT OK

Generic: D84

Current applied

process value: 95.703

mbar

1 Set as 20 mA value

2 Read new value

3 Leave as found

ABORT ENTER

Generic: D84

Set the:

1 4 mA

2 20 mA

3 EXIT

ABORT ENTER

Generic: D84

Apply new 4 mA input

ABORT OK

Generic: D84

Current applied

process value: 96.549

mbar

1 Set as 4 mA value

2 Read new value

3 Leave as found

ABORT ENTER

Generic: D84

AO Alrm typ

EXIT

Generic: D84

HART output

1 Poll addr 0

2 Num req preams 5

3 Burst mode Off

4 Burst option

HELP SAVE HOME

Generic: D84

Analog output

1 AO1 19.920 mA

2 AO Alrm typ

3 Loop test

4 D/A trim

5 Scaled D/A trim

HELP SAVE HOME

Generic: D84

Fld dev output is

fixed at 4.000 mA

ABBR. OK

Generic: D84

Burst mode

Off

Not Used

None

ESC ENTER

Generic: D84

Burst option

*********

% range/current

Process vars/crnt

HELP ESC ENTER

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 39 40

Kommentare zu diesen Handbüchern

Keine Kommentare

Vega D86_D87 Hydrostatic pressure transmitters Bedienungsanleitung Seite 29

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Vega D86_D87 Hydrostatic pressure transmitters