Vega VEGABAR 44 HART Bedienungsanleitung PDF herunterladen (Seite 35)

VEGABAR 44 (HART

) 35

Setup

Note:

After adjustment of a parameter, push "ENTER“ and then "SEND“.

Confirm the message to switch over to manual operation with "OK“.

Confirm the message to reset to automatic operation also with "OK“.

Only then will the adjustment be stored in the sensor and take effect.

1.2.3.1.1

Generic: SENSOR

Current applied

process value :10.945 mbar

1 Set as 4 mA value

2 Read new value

3 Leave as found

ABORT ENTER

1.2.3.1.2

Generic: SENSOR

Current applied

process value:

85.281 mbar

1 Set as 20 mA value

2 Read new value

3 Leave as found

ABORTENTER

Generic: SENSOR

Choose analog output

level

14 mA

2 20 mA

3 Other

4End

ABORT ENTER

Generic: SENSOR

WARN-Loop should be

removed from

automatic control

ABORT OK

Generic: SENSOR

Ser the:

14 mA

2 20 mA

3Exit

ABORT ENTER

Generic: SENSOR

Apply new 20 ma input

ABORT OK

Generic: SENSOR

Current applied

process value:

85.281 mbar

1 Set as 20 mA value

2 Read new value

3 Leave as found

ABORT ENTER

Generic: SENSOR

Set the :

14 mA

2 20 mA

3Exit

ABORT ENTER

Generic: SENSOR

Apply new 4 ma input

ABORT OK

Generic: SENSOR

Current applied

process value:

10.945mbar

1 Set as 4 mA value

2 Read new value

3 Leave as found

ABORT ENTER

Menu windows are displayed but not

supported by the sensor.

Saving of adjustments carried out here is

therefore not possible.

1.4.3.1.3

1.4.3.1.2

Generic: SENSOR

AO Alrm typ

EXIT

Low: In case of failure, current output

goes to 22 mA

High: In case of failure, current output

goes to < 3.6 mA

1.4.3.2

Generic: SENSOR

HART output

1 Poll addr

2 Num req preams 0

3 Burst mode Off

4 Burst option

HELP SAVE HOME

1.4.3.1

Generic: SENSOR

Analog output

1 AO1 13.467mA

2 AO Alrm typ Lo

3 Loop test

4 D/A trim

5 Scaled D/A trim

HELP SAVE HOME

}

Off

Not used

Non

Unused

Special

Generic: SENSOR

Fld dev output is

fixed at 4.000 mA

ABORT O K

Sensor signals measured values only on

request

Sensor signals measured values

unrequested

Choice is not supported

1.4.3.2.3

Generic: SENSOR

Burst mode

Off

Not used

None

Unknown

ESC ENTER

1.4.3.2.4

Generic: SENSOR

Burst option

*************

% range/current

Process vars/crnt

HELP ESC ENTER

Leave the Burst-mode in

OFF-position

Choice is not supported

1.2.3.1.1.1

1.2.3.1.2.1

1.4.3.1.3

1.4.3.1.3.1

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 43 44

Kommentare zu diesen Handbüchern

Keine Kommentare

Vega VEGABAR 44 HART Bedienungsanleitung Seite 35

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Vega VEGABAR 44 HART