Vega TH LINK Version 1.1 Installation Guide Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Kommunikationszubehör Vega TH LINK Version 1.1 Installation Guide herunter. VEGA TH LINK Version 1.1 Installation Guide User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken

Inhaltsverzeichnis

Seite 1 - Installation Guide

Doc. Version 1.1EnglishTH LINKInstallation Guide

Seite 2 - Dear Customer

Design of the TH LINKTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK10Design of the TH LINK(see figure 1)1 Ethernet interface2LE

Seite 3

Design of the TH LINKTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG11Fig. 1: TH LINK (front and side view)TH LINKTrebing &

Seite 4 - About this Installation Guide

Design of the TH LINKTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK12Connections and indicating elements[1] Ethernet interface:

Seite 5 - For your safety

Start-up guidelineTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG13Start-up guidelineThe following steps are required for start-

Seite 6

Installing the TH LINKTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK14Installing the TH LINKInstalling the TH LINKFig. 2: Insta

Seite 7

Connecting to EthernetTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG15Uninstalling the TH LINK1. Remove the connected supply an

Seite 8 - Performance and functioning

Connecting the power supplyTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK16Connecting the power supplyDanger! Electrical voltag

Seite 9 - Ethernet network presettings

Connecting the power supplyTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG17Fig. 3: Terminal strip for power supply on the TH LI

Seite 10 - Design of the TH LINK

Configuring the TH LINK in the Ethernet networkTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK18Configuring the TH LINK in the E

Seite 11

Configuring the TH LINK in the Ethernet networkTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG19SettingsClick on settings and th

Seite 12 - Mounting

Doc. Version 1.1 | May 2012Dear Customer,This installation Guide will help you to install the hardware. If you have any further questions, please co

Seite 13 - Start-up guideline

Configuring the TH LINK in the Ethernet networkTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK20User administrationHere you can

Seite 14 - Installing the TH LINK

Configuring the TH LINK in the Ethernet networkTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG21Configuration method (DHCP/Manua

Seite 15 - Connecting to Ethernet

Configuring the TH LINK in the Ethernet networkTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK22Connection in a network with man

Seite 16 - Connecting the power supply

Configuring the TH LINK in the Ethernet networkTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG23Setting new IP and network addre

Seite 17 - Earth conductor

Configuring the TH LINK in the Ethernet networkTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK244. If you want to use a DNS serv

Seite 18

TH SCOPE settingsTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG25TH SCOPE settingsClick on settings > TH SCOPE.Here you can

Seite 19 - Settings

TH SCOPE settingsTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK26MeasurementThe measurement settings include among other settin

Seite 20 - Operation mode

TH SCOPE settingsTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG27Apply parametersBy default all TH LINK are set as parameter re

Seite 21

Connecting the PROFIBUSTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK28Connecting the PROFIBUSThe 9-pin D-Sub socket is used fo

Seite 22 - Default gateway 0.0.0.0

Connecting the PROFIBUSTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG29Fig. 7: Interface connection possibilities in the PROFIB

Seite 23

ContentAbout this Installation Guide ...4Intended use ...

Seite 24

Connecting the PROFIBUSTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK30Bus terminating resistorsTerminations of a PROFIBUS segm

Seite 25 - TH SCOPE settings

Firmware updateTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG31Firmware updateFirmware updates for the TH LINK are available fr

Seite 26 - Set parameter provider

TroubleshootingTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK32Troubleshooting– Check the power supply (LED RUN must light gree

Seite 27 - Parameters

TroubleshootingTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG33– Internal error or defect: Please contact the Technical Support

Seite 28 - Connecting the PROFIBUS

Technical dataTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK34Technical dataElectrical dataNominal supply voltage (limit value

Seite 29

General conditionsTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG35General conditionsRight to make additions or alterationsTrebi

Seite 30 - Setting PROFIBUS parameters

Doc.Nr. 10003010 © Trebing & Himstedt Prozeßautomation GmbH & Co. KG

Seite 31 - Firmware update

About this Installation GuideTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK4About this Installation GuidePlease read this insta

Seite 32 - Troubleshooting

For your safetyTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG5Menu and keyboard commandsThe following conventions apply to menu

Seite 33

For your safetyTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK6– Carefully plan the integration of the TH LINK into an existing

Seite 34 - Technical data

For your safetyTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG7– High temperature differences between the storage site and insta

Seite 35 - General conditions

Performance and functioningTrebing & Himstedt Prozeßautomation GmbH & Co. KG | TH LINK8Performance and functioningThe TH LINK provides acces

Seite 36

Performance and functioningTH LINK | Trebing & Himstedt Prozeßautomation GmbH & Co. KG9Configuration requirements(not included in the scope

Kommentare zu diesen Handbüchern

Keine Kommentare