Designation:Order No.:PSI-DATA/FAX-MODEM/RS232 Industrial ModemPSI-DATA/FAX-MODEM/RS232 UM E26 99 35 4User Manual
Table of Contentsiv 692302
PSI-DATA/FAX-MODEM/RS2326-12 692302&W Save Active ConfigurationThis command saves the active configuration in the permanent memory.&X Synchron
AT Commands692302 6-13%G Caller ID%P Power-On Auto-ConnectThe %P command specifies whether the modem automatically establishes a connection with anoth
PSI-DATA/FAX-MODEM/RS2326-14 692302*A Configuration of the Switching Input*F Reset ModemThe AT*F command returns the modem to its default state.*P=x S
AT Commands692302 6-156.2 AT Commands for MNP and LAPM (V.42bis)%An Auto Reliable FallbackThe %A command specifies which character forces the modem to
PSI-DATA/FAX-MODEM/RS2326-16 692302\C Set MNP BufferThe \C specifies whether the modem stores received data in the buffer memory while both modems are
AT Commands692302 6-17\J Set Serial Data Transmission SpeedThe \J command specifies whether the data transmission speed between your modem and your co
PSI-DATA/FAX-MODEM/RS2326-18 692302\N V.42/MNP Data ConnectionThe \N command specifies what type of data connection your modem can establish (MNP or L
AT Commands692302 6-19\X Forward XON/XOFFWhen the command for software-controlled data flow control (\G1) is activated, the PC and modem execute data
PSI-DATA/FAX-MODEM/RS2326-20 6923026.3 V.250 Commands ImplementedA Manual AnsweringD DialingE EchoH Hook (Hang Up)I IdentificationL Volume ControlM Sp
AT Commands692302 6-216.4 S RegistersYour modem has 105 registers (S0 through S104). These registers influence the operating characteristics of the mo
Section 1692302 1-1This section provides information about– The data for the industrial modemPSI-DATA/FAX-MODEM/RS232 Industrial Modem ...
PSI-DATA/FAX-MODEM/RS2326-22 692302Description of the S RegistersS0 Number of Rings Before Automatically Answering (Auto Answer)Register S0 specifies
AT Commands692302 6-23S5 BackspaceRegister S5 specifies the ASCII value of the backspace character. This character is generated when the backspace key
PSI-DATA/FAX-MODEM/RS2326-24 692302S9 Waiting Time for Detecting the Carrier Detect SignalRegister S9 specifies how long the carrier detect signal for
AT Commands692302 6-25S12 Waiting Time for Detecting the Escape CharacterRegister S12 specifies how long your modem should wait once the Escape string
PSI-DATA/FAX-MODEM/RS2326-26 692302S23 Modem Control Register (Bit-Mapped)Register S23 specifies the status of DTE data rate, parity, and monitoring t
AT Commands692302 6-27S93 to S103 ReservedS104 Maximum Connection TimeThis register controls the maximum connection time in minutes. Regardless of the
PSI-DATA/FAX-MODEM/RS2326-28 6923026.5 Bell/CCITT ModeThe B command can be used to set the transmission method (see page 6-5).Table 6-1 Bell/CCITT mod
AT Commands692302 6-296.6 Modem ConfirmationsThe X command can be used to control the way in which your modem responds to specific events (see page 6-
PSI-DATA/FAX-MODEM/RS2326-30 692302CONNECT 75/1200 1,2,3,4 22 75/1200 bps connection established.CARRIER 300 1,2,3,4 40 Connection with 300 bps carrie
AT Commands692302 6-316.7 Processing the Break CharacterThe \K command specifies one of three options for processing the break character (see page 6-1
PSI-DATA/FAX-MODEM/RS2321-2 692302
PSI-DATA/FAX-MODEM/RS2326-32 692302Table 6-5 Break character received by the PC while the modem is connected via an MNP or standard connection in data
Section 7692302 7-1This section provides information about– Configurations for various connectionsConfiguration Help...
PSI-DATA/FAX-MODEM/RS2327-2 692302
Configuration Help692302 7-37 Configuration Help7.1 Programming Connection for Phoenix Contact ControllersIf you wish to use the modem in conjunction
PSI-DATA/FAX-MODEM/RS2327-4 692302Configuration of the ModemThe modem must be configured as follows when connecting to Phoenix Contact controllers:The
Configuration Help692302 7-57.2 Programming Connection for Siemens S7 300/400A TS adapter (Siemens Part No. 6ES7 972 - 0CA34-0XA0) is required to conn
PSI-DATA/FAX-MODEM/RS2327-6 692302The interface on the PC must be set as follows:– 9600 bps (or 38,400 bps)– 8 data bits– No parity– 1 stop bitConfigu
We Are Interested in Your Opinion!We would like to hear your comments and suggestions concerning this document.We review and consider all comments for
5050df17 FAX ReplyPhoenix Contact GmbH & Co. KG Date: Marketing ServicesDokumentation Fax No: +49 - (0) 52 35 34 18 8From:Company: Name:Departmen
PSI-DATA/FAX-MODEM/RS232 Industrial Modem692302 1-31 PSI-DATA/FAX-MODEM/RS232 Industrial Modem1.1 DescriptionThe PSI-DATA/FAX-MODEM/RS232 DIN-rail mou
PSI-DATA/FAX-MODEM/RS2321-4 6923021.2 ApplicationThe PSI-DATA/FAX-MODEM/RS232 modem can be used universally throughout the world for all popular modem
PSI-DATA/FAX-MODEM/RS232 Industrial Modem692302 1-51.3 Ordering Data TypeOrder No.Pcs.pkt.Analog modem, DIN-rail mountable, dial-up and standard line
PSI-DATA/FAX-MODEM/RS2321-6 6923021.4 Technical Data1.4.1 SupplySupply voltageFrequencyCurrent Consumption- Nominal operation- Sleep mode (configurabl
PSI-DATA/FAX-MODEM/RS232 Industrial Modem692302 1-71.4.3 PSTN Port (a/b Line)ConnectionShieldOperating modesDial-up methodTransmission rate- DCE/DCE-
PSI-DATA/FAX-MODEM/RS2321-8 6923021.4.4 Switching Input and OutputSwitching input UNom 24 V DC/5 mA, input range 9...48 V DC, electrically isolated.Ac
PSI-DATA/FAX-MODEM/RS232 Industrial Modem692302 1-91.4.6 General DataCE conformanceApprovalsTelecommunications approvalsAmbient operating temperature
PSI-DATA/FAX-MODEM/RS2321-10 692302c1.5 CE ConformityConforms to the EMC Directive 89/336/EECEMC (Electromagnetic Compatibility)Noise immunity accordi
Section 2692302 2-1This section provides information about– The data for the industrial modemQuick Installation of a Dial-up Connection...
PSI-DATA/FAX-MODEM/RS2322-2 692302
Quick Installation of a Dial-up Connection692302 2-32 Quick Installation of a Dial-up Connection2.1 Hardware Installation2.1.1 Default ConfigurationTh
PSI-DATA/FAX-MODEM/RS2322-4 6923022.1.2 Mounting• Mount the modem on a 35 mm (1.378 in.) EN DIN rail (see Figure 2-1).Figure 2-1 MountingOnly mount an
Quick Installation of a Dial-up Connection692302 2-52.1.3 RS-232 InterfaceThe modem and the PC or another device are connected via the RS-232 cable PS
PSI-DATA/FAX-MODEM/RS2322-6 6923022.1.4 Connecting the Telecommunications CableRJ-12/RJ-11 connectorsConnect the telecommunications cable to an RJ-12/
Quick Installation of a Dial-up Connection692302 2-72.1.5 Supply VoltageConnect the 24 V voltage supply to the "24V" and "0V" conn
PSI-DATA/FAX-MODEM/RS2322-8 6923022.2 Software Installation2.2.1 System RequirementsIn principle, any device can be connected to the modem via a free
Quick Installation of a Dial-up Connection692302 2-92.2.2 Driver Installation• Connect the modem to the PC as described above and switch on the supply
Designation:Revision:Order No.:This user manual is valid for:© Phoenix Contact 12/2003692302User ManualPSI-DATA/FAX-MODEM/RS232 Industrial ModemPSI-DA
PSI-DATA/FAX-MODEM/RS2322-10 692302• Insert the CD-ROM provided into the drive and click on "Next".
Quick Installation of a Dial-up Connection692302 2-11• Click on "Next" to confirm the selection. • To complete the installation, click on &q
PSI-DATA/FAX-MODEM/RS2322-12 692302
Section 3692302 3-1This section provides information about– The installation and connection of your modemHardware Installation...
PSI-DATA/FAX-MODEM/RS2323-2 692302
Hardware Installation692302 3-33 Hardware Installation3.1 StructureHousing DimensionsFigure 3-1 Housing dimensions• Mount the modem on a 35 mm (1.378
PSI-DATA/FAX-MODEM/RS2323-4 692302Figure 3-2 Mounting6 9 2 3 A 0 3 1
Hardware Installation692302 3-53.2 Operating ElementsFigure 3-3 Operating elements3.2.1 Connection Terminals3.2.2 ConnectorsP S I - D A T A / F A X -
PSI-DATA/FAX-MODEM/RS2323-6 6923023.2.3 LEDs3.2.4 Pushbutton14 OH (Green) Off the hook15 AA (Yellow) Automatic answer (automatic call acceptance), fla
Hardware Installation692302 3-73.2.5 DIP SwitchesFigure 3-4 DIP switchesThe DIP switches (1) are located behind the cap (2) on the RS-232 interface. •
PSI-DATA/FAX-MODEM/RS2323-8 692302Switch 4 is only used in the event of an emergency. If automatic baud rate detection has been switched off and the d
Hardware Installation692302 3-93.3.1 Block DiagramFigure 3-5 Block diagrami n -i n +E E P R O Mµ C3278645T x DR x DR T SC T SD S RD T RR IG N D91 D C
PSI-DATA/FAX-MODEM/RS2323-10 6923023.3.2 RS-232 InterfaceThe modem and the PC or another device are connected via the RS-232 cable PSM-KA-9SUB 9/BB/2
Hardware Installation692302 3-11Figure 3-6 RS-232 interfaceTable 3-2 Meaning of the terminal designationsDesignation MeaningDCD (Data Carrier Detect)
PSI-DATA/FAX-MODEM/RS2323-12 6923023.3.3 Telecommunications CableRJ-12/RJ-11 connectorsConnect the telecommunications cable to an RJ-12/RJ-11 connecto
Hardware Installation692302 3-133.3.4 Supply VoltageThe supply voltage must be within the range of 10 V to 60 V DC or 16 V to 40 V AC (50 - 60 Hz). Co
PSI-DATA/FAX-MODEM/RS2323-14 692302
Section 4692302 4-1This section provides information about– The installation of the configuration softwareSoftware Installation ...
PSI-DATA/FAX-MODEM/RS2324-2 692302
Software Installation692302 4-34 Software Installation4.1 System RequirementsIn principle, any device can be connected to the modem via a free RS-232
692302Please Observe the Following Notes:In order to ensure the safe use of your device, we recommend that you read this manual carefully. The followi
PSI-DATA/FAX-MODEM/RS2324-4 6923024.1.1 Driver Installation• Connect the modem to the PC as described above and switch on the supply voltage. After th
Software Installation692302 4-5• Insert the CD-ROM provided into the drive and click on "Next".
PSI-DATA/FAX-MODEM/RS2324-6 692302• Click on "Next" to confirm the selection. • To complete the installation, click on "Finish".Th
Software Installation692302 4-74.2 Configuration SoftwareThe PSI-MODEM-CONF software is used to configure the PSI-DATA/FAX-MODEM/RS232. Your modem has
PSI-DATA/FAX-MODEM/RS2324-8 692302Accepting the terms of the license agreement• Read the terms of the software license agreement thoroughly and click
Software Installation692302 4-9Start copying• Click on "Next" to start copying the files. This may take a few seconds depending on the syste
PSI-DATA/FAX-MODEM/RS2324-10 6923024.2.2 OperationAfter installation, you will find the following icon on your desktop:Starting the software Double-cl
Software Installation692302 4-11Configuring the interfaceFirst, you must configure the interface.• Select the "RS-232" function from the &qu
PSI-DATA/FAX-MODEM/RS2324-12 692302• Click on the "Read" button to read data from the connected modem.The software displays the type and v
Software Installation692302 4-13SMSFor this function the modem requires a service provider that supports SMS in the fixed-line network. The modem is p
PSI-DATA/FAX-MODEM/RS232692302Statement of Legal AuthorityThis manual, including all illustrations contained herein, is copyright protected. Use of th
PSI-DATA/FAX-MODEM/RS2324-14 692302Fax• To activate the fax function select the "Fax" checkbox.• Enter the telephone number of the fax recei
Software Installation692302 4-15Switching Output• To activate the switching output function select the "Output" checkbox.• Enter the telepho
PSI-DATA/FAX-MODEM/RS2324-16 692302• Specify the modem mode:– In "Set" mode the modem responds to a positive edge on the local input by call
Software Installation692302 4-17File FunctionsProfile SettingsClick on the "Settings" button . This opens the "Profile settings"
PSI-DATA/FAX-MODEM/RS2324-18 692302Echo If the echo is on, all characters sent by the PC in command mode are sent back by the modem. The characters ca
Software Installation692302 4-19Result Codes Your modem is configured so that it outputs alphanumeric responses on-screen. The "Numeric" opt
PSI-DATA/FAX-MODEM/RS2324-20 692302SMS Mode When SMS mode is disabled, you can only send SMS messages. In addition, your service provider must support
Software Installation692302 4-21SMS Provider The number for the SMS provider must be stored in the modem memory. It is set to Deutsche Telekom by defa
PSI-DATA/FAX-MODEM/RS2324-22 692302Caller ID Mode Caller ID or CLIP (Calling Line Identification Presentation) is the transmission of the caller’s tel
Software Installation692302 4-23• Click on the "Write" button to write the settings to the modem once they have all been entered.
692302 iTable of Contents1 PSI-DATA/FAX-MODEM/RS232 Industrial Modem ... 1-31.2 Application...
PSI-DATA/FAX-MODEM/RS2324-24 692302
Section 5692302 5-1This section provides information about– The additional functions of your modemSpecial Functions ...
PSI-DATA/FAX-MODEM/RS2325-2 692302
Special Functions692302 5-35 Special Functions5.1 Permanent LineThe PSI-DATA/FAX-MODEM/RS232 modem supports 2-wire permanent line operation.– DIP swit
PSI-DATA/FAX-MODEM/RS2325-4 6923025.2 Alarm Inputs and AlarmsThe PSI-DATA/FAX-MODEM/RS232 modem has one electrically isolated input and one electrical
Special Functions692302 5-5The number and the password for the partner must be entered for the OUT configuration. The option can be set to "0&quo
PSI-DATA/FAX-MODEM/RS2325-6 692302Alarm at the Input:In the event of an alarm at input 1, the alarm message "INPUT 1 ACTIVE" is first sent t
Special Functions692302 5-75.3 Password Protection5.3.1 Selecting a PasswordExample– *P=x commandStores a password in the permanent memoryThe *P=x com
PSI-DATA/FAX-MODEM/RS2325-8 6923025.3.3 Password-Protected Call BackThe %S1 command enables password-protected call back. If you wish to activate this
Special Functions692302 5-95.4 Caller ID and Selective Call Acceptance5.4.1 Caller ID OutputCaller ID or CLIP (Calling Line Identification Presentatio
Table of Contentsii 6923023 Hardware Installation...
PSI-DATA/FAX-MODEM/RS2325-10 692302end with these digits are considered as valid. The number of preceding digits is of no importance. The advantage of
Special Functions692302 5-115.5.2 DTMF ControlThe modem is called by a telephone or calls a telephone. The partner uses DTMF tones and sends control c
PSI-DATA/FAX-MODEM/RS2325-12 6923025.6 ASCII to Fax ConversionThe PSI-DATA/FAX-MODEM/RS232 supports ASCII to fax conversion. The modem can automatical
Special Functions692302 5-13Table 5-2 DOS UmlautsDOS Umlaut ASCII Character84hexä94hexö81hexü8EhexÄ99hexÖ9AhexÜE1hexßTable 5-3 Windows UmlautsWindows
PSI-DATA/FAX-MODEM/RS2325-14 6923025.7 SMS in the Fixed-Line NetworkYou can send and receive SMS messages in the Deutsche Telekom fixed-line network w
Special Functions692302 5-15SMS messages are preceded by the caller ID (CLIP) of the service provider. The caller ID is not transmitted until after th
PSI-DATA/FAX-MODEM/RS2325-16 6923025.7.3 Control via SMS MessagesThe PSI-DATA/FAX-MODEM/RS232 can be controlled via SMS messages. For example, you can
Special Functions692302 5-175.8 Setting a Partner Output5.8.1 Transmitting Local Inputs to the Partner OutputThe PSI-DATA/FAX-MODEM/RS232 modem has on
PSI-DATA/FAX-MODEM/RS2325-18 692302
Section 6692302 6-1This section provides information about– The various AT commandsAT Commands...
PSI-DATA/FAX-MODEM/RS232692302 iii5.5 DTMF... 5-105.5
PSI-DATA/FAX-MODEM/RS2326-2 692302
AT Commands692302 6-36 AT CommandsYour modem stores its operating characteristics in a non-volatile memory (EEPROM). These characteristics can be over
PSI-DATA/FAX-MODEM/RS2326-4 692302Repeating the Previous CommandYou can instruct your modem to repeat the last command by entering A/ in command mode.
AT Commands692302 6-5B Set Transmission MethodThe B command can be used to operate your modem in Bell and/or CCITT mode depending on the DTE baud rate
PSI-DATA/FAX-MODEM/RS2326-6 692302DS=n Dial One of the Stored Telephone NumbersThe DS=n command instructs the mode to dial one of 20 telephone numbers
AT Commands692302 6-7+++ Escape StringThe escape string can be used to switch your modem from data mode to command mode without losing the connection
PSI-DATA/FAX-MODEM/RS2326-8 692302O Data Mode/Fall Forward/Fall BackwardThis function is useful if errors emerge, e.g., due to modifying the telephone
AT Commands692302 6-9T Tone Frequency DialingTone frequency dialing is stored by default.V Alpha or Numeric ResponsesYour modem displays responses on-
PSI-DATA/FAX-MODEM/RS2326-10 692302Y Break SignalZ ResetUse the Z command to reset your modem. Your modem then hangs up and loads configuration profil
AT Commands692302 6-11&K Set DTE Flow ControlThe &K command specifies the type of data control that is set between the modem and the local PC
Kommentare zu diesen Handbüchern